head 1.2; access; symbols micropython-1-5-2-base:1.1.1.1 MICROPYTHON:1.1.1; locks; strict; comment @ * @; 1.2 date 2026.10.15.05.28.56; author agc; state dead; branches; next 1.1; commitid aHLdC1EGCUYk7xZG; 1.1 date 2016.01.14.01.38.50; author agc; state Exp; branches 1.1.1.1; next ; commitid Q8liT0v6zMF95QQy; 1.1.1.1 date 2016.01.14.01.38.50; author agc; state Exp; branches; next ; commitid Q8liT0v6zMF95QQy; desc @@ 1.2 log @Remove waaaay old micropython sources which haven't been relevant for 10 years @ text @#define STM32F7DISC #define MICROPY_HW_BOARD_NAME "F7DISC" #define MICROPY_HW_MCU_NAME "STM32F746" #define MICROPY_HW_HAS_SWITCH (1) #define MICROPY_HW_HAS_SDCARD (1) #define MICROPY_HW_HAS_MMA7660 (0) #define MICROPY_HW_HAS_LIS3DSH (0) #define MICROPY_HW_HAS_LCD (0) #define MICROPY_HW_ENABLE_RNG (1) #define MICROPY_HW_ENABLE_RTC (1) #define MICROPY_HW_ENABLE_TIMER (1) #define MICROPY_HW_ENABLE_SERVO (0) #define MICROPY_HW_ENABLE_DAC (0) #define MICROPY_HW_ENABLE_CAN (1) #define MICROPY_BOARD_EARLY_INIT STM32F7DISC_board_early_init void STM32F7DISC_board_early_init(void); // HSE is 25MHz #define MICROPY_HW_CLK_PLLM (25) #define MICROPY_HW_CLK_PLLN (336) #define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) #define MICROPY_HW_CLK_PLLQ (7) #define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_6 // UART config #define MICROPY_HW_UART1_TX_PORT (GPIOA) #define MICROPY_HW_UART1_TX_PIN (GPIO_PIN_9) #define MICROPY_HW_UART1_RX_PORT (GPIOB) #define MICROPY_HW_UART1_RX_PIN (GPIO_PIN_7) #define MICROPY_HW_UART6_PORT (GPIOC) #define MICROPY_HW_UART6_PINS (GPIO_PIN_6 | GPIO_PIN_7) #define MICROPY_HW_UART7_PORT (GPIOF) #define MICROPY_HW_UART7_PINS (GPIO_PIN_6 | GPIO_PIN_7) #define MICROPY_HW_UART_REPL PYB_UART_1 #define MICROPY_HW_UART_REPL_BAUD 115200 // I2C busses #define MICROPY_HW_I2C1_SCL (pin_B8) #define MICROPY_HW_I2C1_SDA (pin_B9) #define MICROPY_HW_I2C3_SCL (pin_H7) #define MICROPY_HW_I2C3_SDA (pin_H8) // The STM32F7 uses a TIMINGR register which is configured using an Excel // Spreadsheet from AN4235: http://www.st.com/web/en/catalog/tools/PF258335 // We use an array of baudrates and corresponding TIMINGR values. // // The value 0x40912732 was obtained from the DISCOVERY_I2Cx_TIMING constant // defined in the STM32F7Cube file Drivers/BSP/STM32F746G-Discovery/stm32f7456g_discovery.h #define MICROPY_HW_I2C_BAUDRATE_TIMING {{100000, 0x40912732}} #define MICROPY_HW_I2C_BAUDRATE_DEFAULT 100000 #define MICROPY_HW_I2C_BAUDRATE_MAX 100000 // SPI #define MICROPY_HW_SPI2_NSS (pin_I0) #define MICROPY_HW_SPI2_SCK (pin_I1) #define MICROPY_HW_SPI2_MISO (pin_B14) #define MICROPY_HW_SPI2_MOSI (pin_B15) // USRSW is pulled low. Pressing the button makes the input go high. #define MICROPY_HW_USRSW_PIN (pin_I11) #define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) #define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) #define MICROPY_HW_USRSW_PRESSED (1) // LEDs #define MICROPY_HW_LED1 (pin_I1) // green #define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP) #define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRR = pin->pin_mask) #define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRR = (pin->pin_mask << 16)) // SD card detect switch #define MICROPY_HW_SDCARD_DETECT_PIN (pin_C13) #define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP) #define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET) // USB config (CN13 - USB OTG FS) // The Hardware VBUS detect only works on pin PA9. The STM32F7 Discovery uses // PA9 for VCP_TX functionality and connects the VBUS to pin J12 (so software // only detect). So we don't define the VBUS detect pin since that requires PA9. /*#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_J12)*/ #define MICROPY_HW_USB_OTG_ID_PIN (pin_A10) @ 1.1 log @Initial revision @ text @@ 1.1.1.1 log @Import micropython version 1.5.2 into othersrc. Micropython is a python3 implementation that has been optimised for micro-controllers and small embedded systems. It also has a "unix" port. It has an MIT license. This is version 1.5.2 of micropython. MicroPython implements the entire Python 3.4 syntax (including exceptions, "with", "yield from", etc.). The following core datatypes are provided: str (including basic Unicode support), bytes, bytearray, tuple, list, dict, set, frozenset, array.array, collections.namedtuple, classes and instances. Builtin modules include sys, time, and struct. Note that only subset of Python 3.4 functionality implemented for the data types and modules. This is the standard micropython source (version v1.5.2), which has been adapted to use reachover infrastructure. At the present time, libffi (from pkgsrc) is used. Alternative locations for libffi can be set using the PKGSRC_PREFIX definition to make. In the whole scheme of things, micropython is quite small: % size bin/micropython text data bss dec hex filename 393495 1624 2208 397327 6100f bin/micropython % and runs much as expected: % bin/micropython MicroPython v1.5.2 on 2016-01-13; linux version Use Ctrl-D to exit, Ctrl-E for paste mode >>> print("hello world") hello world >>> list(5 * x + y for x in range(10) for y in [4, 2, 1]) [4, 2, 1, 9, 7, 6, 14, 12, 11, 19, 17, 16, 24, 22, 21, 29, 27, 26, 34, 32, 31, 39, 37, 36, 44, 42, 41, 49, 47, 46] >>> % python2.7 Python 2.7.10 (default, Oct 17 2015, 17:55:29) [GCC 4.8.5] on netbsd7 Type "help", "copyright", "credits" or "license" for more information. >>> print("hello world") hello world >>> list(5 * x + y for x in range(10) for y in [4, 2, 1]) [4, 2, 1, 9, 7, 6, 14, 12, 11, 19, 17, 16, 24, 22, 21, 29, 27, 26, 34, 32, 31, 39, 37, 36, 44, 42, 41, 49, 47, 46] >>> ^D % This (reachover) version runs all the tests which the gmake version does. % make t cd bin && make t cd /home/agc/local/micropython/bin/../dist/unix/../tests && env MICROPY_MICROPYTHON=/home/agc/local/micropython/bin/micropython ./run-tests pass basics/0prelim.py pass basics/andor.py pass basics/array1.py pass basics/array_add.py pass basics/array_construct.py pass basics/array_construct2.py ... pass unix/ffi_callback.py pass unix/ffi_float.py pass unix/ffi_float2.py 474 tests performed (15812 individual testcases) 474 tests passed 5 tests skipped: cmd_showbc cmd_verbose machine1 machine_mem extra_coverage % The sources are available from github: https://github.com/micropython/micropython micropython release at: https://github.com/micropython/micropython/releases Sources for 1.5.2 taken from: https://github.com/micropython/micropython/archive/v1.5.2.tar.gz Alistair Crooks agc@@netbsd.org Wed Jan 13 17:15:30 PST 2016 @ text @@